Carsets

  • Accueil
  • > Archives pour novembre 2016

29 novembre 2016

FVDI2 User Feedback on Mercedes Renault PSA etc

Classé dans : car diagnostic tool — carsets @ 8 h 55 min

Here are some good or bad reviews/reports of Fly FVDI 2nd generation FVDI2 arbites commander from customers.  FVDI2 are tested on vag group vehicles, mercedes/smart, renault, porsche, ford, opel… Some worked, some failed.

 

–> FVDI2 test on Mercedes and Smart

 

– Brand/Model of car : Mercedes SL W230
– Year of car : 2004
– Feature in relation : SBC REPAIR
– Version of FVDI : 6.4
– Result : OK

 

– Brand/Model of car : Mercedes A170
– Year of car : 2005
– Feature in relation : Dash km
– Version of FVDI : Mercedes/Smart/Maybach V5.11
– Result : OK

 

– Brand/Model of car : Mercedes w204

– Result: damage zgw, go to mb dealer

 

– Brand/Model of car : SMART 450 600 – 700 cc
– Year of car : 2000 and 2003
– Feature in relation : key teach
– Version of FVDI : 6.4
– Result : OK

 

– Brand/Model of car : Smart ForTwo
– Year of car : 2000
– Feature in relation : remote programming
– Version of FVDI : Smart 7.0
– Result : OK

 

– Brand/Model of car : mercedes W211 E220
– Year of car : 2007
– Feature in relation : missed key dissable in EZS
– Version of FVDI : 6.4
– Result : OK

 

 

–> FVDI2 VAG commander test results:

 

– Brand/Model of car : Skoda Roomster
– Year of car : 2006
– Feature in relation : pin read and key programming
– Version of FVDI : VAG 24.0
– Result : OK

 

– Brand/Model of car : golf 6 TDI 2012
– Feature in relation : with CS (component protection ) , pin read and key programming
– Result : ok

 

– Brand/Model of car : VW Passat 3C 2.0tdi
– Year of car : 2007
– Feature in relation : learning key
– Version of FVDI : OLD 18
– Result : ok 

 

– Brand/Model of car :Seat Leon 1PA

– Year of car : 2011
– Version of FVDI : fvdi 21
– Feature in relation :add new key
– Result : successfully

 

– Brand/Model of car : Audi A4

– Year of car : 2000

– Feature in relation : Key learning + mileage correction
– Result : OK!

 

– Brand/Model of car : VAG
– Year of car : 1998-2002
– Feature in relation : pin read from EDC15
– Version of FVDI : VAG 24.0
– Result : Error (can’t connected)

 

– Brand/Model of car : Audi A4
– Year of car : 2003
– Feature in relation : pin read and key programming cluster RB4 crypto
– Version of FVDI : VAG 24.0
– Result : Error
After read pin, eeprom content in RB4 faulty. Car don’t recognized original key. Solved by write content saved after first read.

 

– Brand/Model of car : VW Caravelle
– Year of car : 2001
– Feature in relation : transponder programming from dump
– Version of FVDI : Tagkey Tool 6.2
– Result : Error (4pcs. PCF7935 damaged)
Dump recognized good, pin readed correctly. Problem solved programming prepared PCF7935 to VW id44 via OBD.

 

 

–> Flyobd FVDI2 abrites for Opel test results:

 

– Brand/Model of car : Opel Zafira B
– Year of car : 2006
– Feature in relation : pin read and key programming
– Version of FVDI : Opel 6.6
– Result : OK

 

– Brand/Model of car : Opel Vectra C

– Year of car : 2005

– Feature in relation : DTC read and remove on ABS

– Result : OK!

 

– Brand/Model of car : Opel Zafira

– Year of car : 2004

– Feature in relation : mileage correction
– Result : OK!

 

– Brand/Model of car : Opel Zafira

– Year of car : 2006

– Feature in relation : mileage correction

– Result : OK!

 

 

–> Fly obd FVDI2 Renault test results:

 

– Brand/Model of car : Renault Scenic 2
– Year of car : 2004
– Feature in relation : Key Learning (keycard pcf 7947)
– Version of FVDI : 5.2
– Result : Ok

 

– Brand/Model of car : Renault Scenic II ph2 1.5 dci
– Year of car : 2009
– Feature in relation : learning key
– Version of FVDI : 5.2
– Result : ok

 

– Brand/Model of car : Renault Clio 2
– Year of car : 2010
– Feature in relation : Key learning
– Version of FVDI : 5.2
– Result : Ok

 

– Brand/Model of car : Renault Kangoo DCi 1.5 ecu Delphi TRW DDCR 1.5 DCi
– Year of car : 2005
– Feature in relation : Transponder learning 7936
– Version of FVDI : 5.2
– Result : ok

 

– Brand/Model of car : Renault clio classic petrol
– Year of car : 2004
– Feature in relation : reading pin
– Version of FVDI : 5.2
– Result : Ok

 

– Brand/Model of car : Renault Megane 3
– Year of car : 2013
– Feature in relation : tacho correction
– Version of FVDI : 5.04
– Result : OK

 

– Brand/Model of car : Renault Megane 2
– Year of car : 2008
– Feature in relation : Dash Km
– Version of FVDI : 5.2
– Result : Ok

 

– Brand/Model of car : Renault Espace
– Year of car : 2006
– Feature in relation : pin read and key programming
– Version of FVDI : Renault 6.3
– Result : OK

 

– Brand/Model of car : Renault Grand Scenic
– Year of car : 2005
– Feature in relation : pin read and key programming
– Version of FVDI : Renault 6.3
– Result : OK

 

– Brand/Model of car : Renault Traffic
– Year of car : 2004
– Feature in relation : pin read and key programming from UCH dump
– Version of FVDI : Tagkey Tool 6.2
– Result : OK

 

– Brand/Model of car : Renault symbol 1.2
– Year of car : 2011
– Feature in relation : read pin
– Version of FVDI : 5.2
– Result : not ok

 

 

–> FVDI2 Commander PSA test reports:

 

– Brand/Model of car : Citroen C2

– Year of car : 2005

– Feature in relation : mileage correction

– Result : OK!
– Brand/Model of car : Citroen C3

– Year of car : 2006

– Feature in relation : mileage correction

– Result : OK!
– Brand/Model of car : Peugeot Expert

– Year of car : 2008

– Feature in relation : Key code + learning
– Result : OK!

 

– Brand/Model of car : Peugeot Expert

– Year of car : 2012

– Feature in relation : Key code + learning
– Result : OK!

 

– Brand/Model of car : Citroen C5

– Year of car : 2008 1.6hdi

– Feature in relation : bsi -JC – NOT WORK
– Result : IT IS DEAD BSI. 

 

– Brand/Model of car : PEUGEOT 308
– Year of car : 2010 2010 2011
– Feature in relation : PIN READ
– Version of FVDI : 6.3
– Result : DANGEROUS

 

 

–> Test of FVDI2 and other brands of cars:

 

– Brand/Model of car : Ford focus

– Year of car : 2012

– Feature in relation : read km

– Result : ok

 

– Brand/Model of car : Porsche Boxster S (986)

– Year of car : year 2002
– Feature in relation : Read radio pin by obd, Mileage correction by obd

– Result : OK !
– Brand/Model of car : Fiat Idea 1.3 m-jet
– Year of car : 2004
– Feature in relation : change km
– Version of FVDI : 5.4
– Result : ok

 

– Brand/Model of car : Jeep Grand Cherokee

– Year of car : 2005 – on
– Feature in relation : Read IMMO pin number & Mileage correction by OBD

– Result : OK !

Note: when “get current mileage” is displayed in abrites it is in KM ok. (it does not say KM or Miles)
When changed data, it says success ! but dash wont change until car drive short distance then noise; bong ! mileage adjust to correction ok.

http://blog.obdii365.com/2016/11/29/test-report-of-fvdi2-on-renault-vag-mercedes-psa/

25 novembre 2016

How to Program Chevrolet Prisma Key via OBDSTAR

Classé dans : car key programmer — carsets @ 7 h 26 min
Here is the instruction on programming remote key for GM Chevrolet New Prisma by using OBDSTAR X300 Pro3 Key Master auto key programmer.
In Brazil, there’s a Chevrolet model called the Prisma locally produced by General Motors in Gravatai.t’s basically the low-cost version of the Sonic, but it’s actually cool in its own way and, more importantly, it’s been updated for the 2015 model year and now it comes with lots of goodies for a tiny dribble of money.
Instruction:
Connect X300 Pro3 with vehicle via OBD socket
Select vehicle Brand:GM
Select Immo/Remote
Select Immo/Remote
Select Chevrolet
Select Chevrolet
Select Cruze (there is no Prisma option under OBDSTAR Key Master Chevrolet list, select Cruze)
Select Cruze
Select Without Smart
Select Without Smart
Select All keys lost
Select All keys lost
Enter security code and confirm
enter-security-code
Switch ignition off for 5 sec, and then switch ignition on
Configuring the system, wait for about 10-minutes
Switch ignition off , remove the key
Open and close the driver door, confirm all electrical closed
Turn on the ignition switch.
Whether to program next key?
Switch ignition off , remove the key
Insert a new key, switch ignition on
insert-a-new-key
Switch ignition off , remove the key
Open and close the driver door, confirm all electrical closed
Turn on the ignition switch
Whether to program next key?
Switch ignition off , remove the key
Open and close the driver door, confirm all electrical closed
Configuring the system, wait for about 45 sec
Turn on the ignition switch
Switch ignition off
Turn on the ignition switch
Program Complete
program-complete
Start car with new programmed key
It is working.
https://eobd21.wordpress.com/2016/11/25/program-key-on-gm-new-prisma-by-obdstar-key-master/

24 novembre 2016

How to Install V162 Renault CAN CLIP on Win XP

Classé dans : car diagnostic tool — carsets @ 7 h 45 min

Renault CAN CLIP interface V162 diagnostic software has been verified working without any issues by obdii365 engineers. Here is the instruction on how to install CAN CLIP V162 on Windows xp system.

Update:
via CD (Renault CAN CLIP v162 software CD)
Operating system:
Windows XP
Model coverage:
Renault 1998-2016
CAN CLIP v162 function:
Professional diagnosis on ENGINE, automatic gear shifting, Air conditioning system, SRS, ABS, ASR, MPL, GM, IMMO, KEYZESS GO system, OBD-I I and so on.
New models in CLIP 162:
XBB
CLIP 162 installation:

Step-by-step installation:

Step 1 – run Crack Renault CAN CLIP
Insert CAN CLIP 162 disk E: and open it.
Copy Activation(Patch V3) to Desktop
Open Crack Renault CLIP registration entries
Register Editor: click Yes.
Click OK.
Step 2 – install Renault CLIP 162
Run setup.exe
CLIP V162 is running automatically
Click the laptop icon (FIRST INSTALLATION) in CLIP V162 interface.
FIRST INSTALLATION
Click “I accept…agreement” and click Next.
Select country. (here, select OTHER COUNTRY). and click Next.
Select language and click Next.
select-language
Manufacturer:Renault. click Next.
Click Next to begin copying files.
Click Next to install Windows resources kit tools
Accept the agreement
Then next
Install now
Successfully installed Windows resources kit tools
installed Windows resources kit tools
Installing clip….
Renault can clip installation success
 installation success
RESTART your computer
Step 3 – setup CLIP properties
Open CLIP properties on Desktop
Open file location:
Cut RSRWin application in local disk C:/ CLIP_X91/ Lib/ Application
Paste RSRWin application on Desktop
Close CLIP properties
Replace RSRWin with another RSRWin application in Computer/renault can clip disk E:/Activation(Patch V3)
Step 4 – register CLIP
Run RSRWin application in local disk C:/ CLIP_X91/ Lib/ Application
Accept the license and register CLIP
register CLIP
Are you part of the Renault Network? Select No.
Enter the unlocking code with the picture guide Renault Clip Registration Step 4 in the folder Activation(Patch V3)
Activation
then click Confirm.
Registration successful: click OK.
Registration successful
Replace “RSRWin” in C:\CLIP_X91\Lib\Application with”RSRWin” on Desktop
Prompt: installing device driver software…
Prompt: device driver software installed successfully
Step 5 – setup in Computer management
Automatically install driver software
Open computer management
select Device manager->Bosch automotive service solution device->18-alliance vehicle communication interface
select Device manager
close Computer management
Open Display properties
Go to screen saver->power and setup:
power scheme: Always on
Turn off monitor: never, never
Turn off hard disk: never, never
System standby: never, never
Click on Apply, then OK to exit
Click on Apply
Step 6 – open CLIP v162 to begin diagnosis
Run CLIP renault software
There will be a computer security alert. Just click Unlock.
renault-can-clip-v162-1
renault-can-clip-v162-2
renault-can-clip-v162-3
renault-can-clip-v162-4
renault-can-clip-v162-5
Then exit CLIP and run it again
renault-can-clip-v162-6

 

renault-can-clip-v162-7
renault-can-clip-v162-8
renault-can-clip-v162-9
renault-can-clip-v162-10
Done!
Disclaimer:
there are mainly two kinds of China Renault CLIP, but the new Renault CAN CLIP 162 only work with one with the following pcb.
renault-can-clip-pcb-1
renault-can-clip-pcb-2
http://blog.obdii365.com/2016/11/24/install-renault-can-clip-v162-on-windows-xp/

22 novembre 2016

FAQ Original Keyline 884 Decryptor Mini Cloner

Classé dans : car key programmer — carsets @ 3 h 50 min

Keyline 884 Decryptor MINI is a simple device to copy ID48, provides you a wide range of opportunities to copy the keys almost 95% of cars. Here are the FAQ list of the 886 Decryptor.

keyline-884

WHAT DO THE LIGHTS INDICATE?

The green light indicates the Keyline 884 Decryptor Mini is connected to the device. The three red lights indicate the status of the cloning process. When the red light blinks, it means the machine works, and when it is steady, the machine has completed that specific phase. When all lights are on and steady, the cloning process is completed.

 

CAN I PLUG THE 884 DECRYPTOR MINI INTO A POWER OUTLET?

No. 884 Decryptor Mini is designed to be powered by USB / OTG cable when connected to your PC, smartphone or tablet.

keyline-884-mini-faq-power-1

WHAT DOES 884 DECRYPTOR MINI CLONE?

All types of fixed code transponders, first and second generation Texas® Crypto, first and second generation Philips® Crypto, Megamos® Crypto (for VAG models – to be activated with TKM.Starter Kit), Megamos® Crypto (for Kia, Daewoo/Chevrolet, Pontiac), Keyline Keyless Kit and Keyline RFD100. Regarding first generation Philips® Crypto transponder, 884 Decryptor Mini can clone some PH1A; but not PH1B, PH1C, PH1D, PH1E and also Keyline RK60 remote controls. If 884 Decryptor Mini is not able to clone a key, the screen of the smartphone / tablet / PC, will display “Not clonable”.

 

WHAT IS THE BATTERY CONSUMPTION OF THE SMARTPHONE OR TABLET CONNECTED TO 884 DECRYPTOR MINI?

keyline-884-mini-faq-power-2

The consumption is minimum as 884 Decryptor Mini is a device with low power consumption.

 

CAN I CONNECT 884 DECRYPTOR MINI BOTH TO THE PC AND THE SMARTPHONE?

Yes. You need both the software for the PC and Keyline Cloning Tool App for smartphone or tablet. Just make sure to login with the same account on each device.

 

WHY DO I NEED TO CONNECT 884 DECRYPTOR MINI TO THE PC OR TO THE SMARTPHONE?

884 Decryptor Mini is powered by the device it is connected to as well as it works with the Internet access provided by that device.

 

DOES 884 DECRYPTOR MINI WORK WITHOUT INTERNET CONNECTION?

No. 884 Decryptor Mini needs to be connected to the network via PC or smartphone / tablet.

 

I CANNOT CLONE MEGAMOS® KEYS. WHY?

884 Decryptor Mini is designed to clone Megamos® Crypto transponders supported by TKM technology. To enable 884 Decryptor Mini to clone this type of transponder you need the TKM. Starter Kit, which is sold separately.

 

WHAT IF I UNPLUG THE CABLE FROM 884 DECRYPTOR MINI WHILE WORKING?

884 Decryptor Mini immediately stops working if it is no longer powered up.

 

HOW LONG DOES IT TAKE TO CLONE A KEY?

Times are aligned on performance offered by the best tools on the market. The cloning speed depends on the type of key and the Internet connection available in the device which is connected to 884 Decryptor Mini.

 

CAN I USE MY PC OR SMARTPHONE/TABLET FOR OTHER OPERATIONS WHILE CLONING A TRASPONDER?

Yes, it is possible but not recommended. While 884 Decryptor Mini processes data, it is not ideal to do other tasks. It is only recommended to stop the cloning process by pressing “CANCEL”.

 

WHAT HAPPENS IF I LOSE THE INTERNET CONNECTION OR THE PC TURNS OFF?

You need to repeat the procedure with the clonable key that collected the sniffs (when cloning Crypto transponders) and, afterwards, the original key to restart the calculation phase.

 

IS IT POSSIBLE TO WRITE THE KEY AT A LATER TIME?

It is possible to complete the writing process at a later time only for second generation Philips® Crypto transponder and VAG models. It is important to use the original key and follow the sequence of the phases in the cloning procedure.

 

WHAT HAPPENS IF I REMOVE THE ORIGINAL KEY DURING THE CALCULATION?

If the original key is removed after the calculation phase has started, the procedure continues. However, remember the original key must always be inserted in 884 Decryptor Mini when requested from the app or software (depending on the device used) in order to complete the cloning process.

 

WHAT HAPPENS IF I REMOVE THE KEY WHILE WRITING?

It is not advisable, since the writing phase may not be completed and the cloning process may have to be repeated in order to successfully complete the procedure.

 

FAQ About KEYLINE CLONING TOOL APP

HOW DO I DOWNLOAD THE APP?

Log in to the Google Play Store, and type “Keyline Cloning Tool” in the search bar, then select the icon with the Keyline Logo. You can also download the Keyline Cloning Tool App from your PC by accessing https://play.google.com/store?hl

 

HOW CAN I UPDATE 884 DECRYPTOR MINI?

884 Decryptor Mini does not need updates. Just update the Keyline Cloning Tool App, every time an update is made available at the Google Play Store.

 

I FORGOT MY PASSWORD. HOW DO I ACCESS?

You can request a new password directly through the Keyline Cloning Tool App or software, or even from www.keyline.it or www.keyline-usa.com.

 

HOW DO I CONNECT THE SMARTPHONE (OR TABLET) TO 884 DECRYPTOR MINI?

The 884 Decryptor Mini is connected to the PC using the longer cable supplied; to connect 884 Decryptor Mini to the smartphone / tablet use both cables. These must be joined together at the USB ends. The Micro USB end of the longer cable must be connected to 884 Decryptor Mini, while the Micro USB end of the shorter cable (OTG cable) must be connected to the device (smartphone or tablet).

 

WHAT HAPPENS WHEN I RECEIVE A CALL WHILE I AM CLONING A KEY?

As with any app, the current application “pauses” and priority is given to the call. After the phone call you can resume the cloning procedure. In fact, the server continues to work while the App is closed, but remains in background mode.

 

WHY DOES NOT THE SCREEN ROTATE WHILE I AM CLONING?

The calculation is one of the most critical moments in the cloning process. Therefore, it is necessary that Keyline Cloning Tool App works with full computing capacity. The rotation of the screen can slow down the cloning process, so the screen remains fixed.

 

DOES 884 DECRYPTOR MINI WORK WITH ALL SMARTPHONES / TABLET ANDROID?

No. 884 Decryptor Mini is compatible with smartphones / tablets that have OTG or the USB function active. To check if your phone has this feature, simply download the Keyline Cloning Tool App and check in the “Diagnostic” section that the parameter is set to YES USB OTG. It is also recommended to perform a final test to ensure the perfect connection for communication between the device and 884 Decryptor Mini.

884 DECRYPTOR MINI support OTG list

 

DOES 884 DECRYPTOR MINI WORK WITH ALL VERSIONS OF ANDROID?

No, 884 Decryptor Mini works with smartphones and tablets with Android 4.1 and higher.

 

DOES THE KEYLINE CLONING TOOL APPLICATION ACCESS PERSONAL DATA?

No. Keyline Cloning Tool application does not have access to any personal data in the device which is connected to.

 

DOES KEYLINE CLONING TOOL APPLICATION NEED A BROADBAND CONNECTION?

No. Keyline Cloning Tool application requires a stable connection, not necessarily broadband.

 

FAQ About KEYLINE CLONING TOOL SOFTWARE

I FORGOT MY PASSWORD, HOW DO I ACCESS?

You can request a new password through the software interface or by logging in www.keyline.it or www.keyline-usa.com websites. You will receive an e-mail informing you of the change. To activate the new password just click on the link sent to your email address.

 

I DID NOT RECEIVE A REGISTRATION E-MAIL. WHAT DOES IT MEAN?

It is possible that the settings of your system block the reception of some messages. Check in the Spam folder. The sender is Keyline S.p.A.

 

HOW DO I INSTALL THE SOFTWARE?

Follow these few steps: download the software from www.keyline.it or www.keyline-usa.com by clicking on DOWNLOAD SOFTWARE in 884 Decryptor Mini product page. Once the program has been downloaded, click twice to start the installation, then follow the instructions that appear in the interface to complete the installation.

 

WHICH WINDOWS VERSION DOES IT WORKS WITH?

The minimum operating system required is Windows 7 updated to the latest version.

 

I CONNECTED 884 DECRYPTOR MINI TO THE PC BUT I CANNOT CLONE A KEY, WHY?

Check that your PC is connected to Internet and there is a signal (especially for connections via WiFi and USB pen drive). Without internet connection it is not possible to duplicate transponders.

 

I CANNOT DOWNLOAD THE PROGRAM. WHY?

There may be problems due to an Antivirus software or Firewall. Try to temporarily disable them while downloading and installing the software.

 

CAN I TURN OFF 884 DECRYPTOR MINI WHEN CONNECTED TO THE PC?

You can disconnect 884 Decryptor Mini from the PC, only if it is not cloning a transponder.

 

AFTER THE DOWNLOAD AND INSTALLATION OF THE KEYLINE CLONING TOOL SOFTWARE OR APP, CAN I START WORKING WITH 884 DECRYPTOR MINI?

No. After installing Keyline Cloning Tool software or App and connecting 884 Decryptor Mini to your PC / smartphone / tablet – make sure to create an account if you are not registered yet – you must link 884 Decryptor Mini to your account by following these simple steps:

- Login to the account

- Open the Keyline Cloning Tool App or software menu

- Select “My Profile”

- Select “My Products” andclick on the pencil icon. It will show you 884 Decryptor Mini with its serial number

- Click on the the floppy disk icon to save the changes and link 884 Decryptor Mini to your account.

 

CAN I LINK 884 DECRYPTOR MINI TO MORE USERS?

No. 884 Decryptor Mini can be linked to only one account. Therefore, if you want to link 884 Decryptor Mini to a new user you must first unlink it from the current active user.

 

HOW CAN I UNLINK 884 DECRYPTOR MINI?

To unlink 884 Decryptor Mini follow these few simple steps:

- Log in to your account

- Open the Keyline Cloning Tool app or software menu

- Select “My Profile”

- Select “My Products” and click on the pencil icon.

You will see the machines registered on that account

- Cancel the machine you want to unlink from your account by clicking on the “X” next to the drop-down menu

- Click on the floppy disk icon to save the changes.

 http://obd2expresscouk.bcz.com/2016/11/22/keyline-884-decryptor-mini-questions-answers/

Gaskustoms |
Mon Deux-Roues |
Autopassion34 |
Unblog.fr | Créer un blog | Annuaire | Signaler un abus | Handlebar
| Noirmatpeinturecovering
| Coveringmatvoiture