Carsets

  • Accueil
  • > Archives pour octobre 2016

28 octobre 2016

How to Read VW EDC17 C46 by MPPS V18

Classé dans : ECU chip tuning tool — carsets @ 5 h 10 min

I’m trying to read the ECU in my 2011 VW Scirocco with MPPS v18 ECU flasher using the Tricore cable.

mpps-v18-read-edc17-c46-1

And have the ECU out of the vehicle with Tricore cable connected via the following pin out.

mpps-v18-read-edc17-c46-2

However, it still isn’t reading the ECU.

 

Then i Google and most mates say “Only in bootmode for ecu with Tprot.”

Even if i wanna read-it, then i can’t write-it.
So, open the ECU and go with the resistors to the circuit board.
It surely is the only way..

 

But I don’t have any resistors; when I put MPPS in Boot Mode and it gave me the following info…

mpps-v18-read-edc17-c46-3

mpps-v18-read-edc17-c46-4

Then i open the ECU and use resistors to read in Tricore Boot Mode

mpps-v18-read-edc17-c46-5

mpps-v18-read-edc17-c46-6

I think the software should show me what i need to connect. But MPPS just states that this ECU has the new DS Check Routine and that it needs to be opened, therefore using resistors… If someone else wanna do this, better use kess v2 or ktag – both don’t need resistors for this ecu.

 

https://eobd21.wordpress.com/2016/10/28/read-vw-edc17-c46-by-mpps-v18-in-boot-mode/

26 octobre 2016

BMW DASH interface 2.1.0 vehicle not ready solution

Classé dans : car diagnostic tool — carsets @ 4 h 15 min

Here is a solution to BMW DASH v2.02 (which now updated to V2.1.0) interface diagnostic tool  “vehicle not ready” error.

bmw-dash-v2-02-vehicle-not-ready-1

bmw-dash-v2-02-vehicle-not-ready-2

Here take a user real case…

O/S: windows xp 32bit

Model: E87 and E83 (pre-2008)

 

Solutions from obd365.com technicians:

 

Tips: BMW DASH v2.1.0 only works ok on most cars before 2008, but not all. And cars post-2008 hardly works with BMW DASH, but BMW ICOM A2/BMW Creator C310 ok.

 

– make sure com port setup on your PC is the same as that in the software

 

 

BMW Dash interface reference:

1- Models tested ok:

1 Series: E81/E82/E87/E88

3 Series: E30/E36/E46/E90/E91/E92/E93

5 Series: E28/E34/E39/E60/E61

6 Series: E24/E63/E64

7 Series: E23/E32/E38/E65

8 Series: E31

X Series: X3-E83, X5-E53, X5-E70, X5-E71

Z Series: Z1-E30, Z3-E36, Z4-E85/E86, Z5-E52

MINI Series: MINI-R50/R52/R53/R55/R56/R57

 

2- systems tested no issues:

Engine system

Auto Transmission

SRS

ABS

Cruise system

Air-condition system

EWS

LKE

BUS etc.

 

3- functions without issues:

Connecting with all electronic control modules in the vehicle.

For all electronic control units reading identification data, sw/hw versions, user information fields.

For all electronic control units read and clear error (DTCs) memories – standart, shadow, history memory.

Possibility to read/program memory of electronic control units (including CAS modules).

Synchronization DME/DDE and CAS.

bmw-dash-v2-02

http://blog.obdii365.com/2016/10/25/bmw-dash-v210-vehicle-not-ready-solution/

20 octobre 2016

How to install R280 CAS4+ BDM programmer software

Classé dans : ECU chip tuning tool — carsets @ 3 h 17 min

Here is the software installation guide of R280 Plus CAS4 BDM Programmer for BMW Motorola MC9S12XEP100 chip (5M48H/1N35H).

 

NOTE:

Please turn off the anti-virus software before R280 installation, or use anti-virus software is set to be trusted software, so that the installation and use of R280 software.

 

Operating system:

Both Windows xp and Windows 7 worked

 

 

How to install R280 CAS4 Programmer software

 

Insert R208 disk and open it

Copy R280 Plus-3.rar to Desktop and then extract it

Open R280 Plus-3 folder and run R280 Plus.exe

 

Plug in the R280 programmer power supply and USB line

Open R280 Plus properties and find targets in local disk c:/program file/r280 plus/r280 cas4 driver

Run CP210xVCPInstaller.exe to Install the device driver

install-r280-plus-cas4-programmer-1

Click on Cancel in R280 Plus properties

Install software for R280 plus automatically

install-r280-plus-cas4-programmer-2 install-r280-plus-cas4-programmer-3

Install software for Silicon Labs CP210x USB to UART bridge (automatically)

install-r280-plus-cas4-programmer-4 install-r280-plus-cas4-programmer-5

Run “register controls.Bat” MS-DOS Batch File in disk c:/program file/r280 plus

install-r280-plus-cas4-programmer-6

Run R280 Plus software:

First, read M5080 in R270 in circuit programmer

install-r280-plus-cas4-programmer-7

Select MCU M5080

install-r280-plus-cas4-programmer-8

Read M5080

install-r280-plus-cas4-programmer-9

Save the bin file after reading m5080

install-r280-plus-cas4-programmer-10

Second, read 5M48H in R280 cas4 programmer

install-r280-plus-cas4-programmer-11

Select MCU 5M48H to read

install-r280-plus-cas4-programmer-12

Installation complete.

http://blog.obdii365.com/2016/10/19/install-r280-cas4-bdm-programmer-software/

Gaskustoms |
Mon Deux-Roues |
Autopassion34 |
Unblog.fr | Créer un blog | Annuaire | Signaler un abus | Handlebar
| Noirmatpeinturecovering
| Coveringmatvoiture